How To Replace Rubber Gasket On Bathtub Drain

By Admin | February 10, 2024

How To Replace Rubber Gasket On Bathtub Drain

A worn-out or leaking rubber gasket on your bathtub drain can lead to water damage and other issues. Replacing the gasket is a relatively simple task that can be completed in a few minutes with the right tools and materials. Here's a step-by-step guide on how to replace the rubber gasket on your bathtub drain:

Tools and Materials:

- Adjustable wrench - Phillips head screwdriver - Flathead screwdriver - New rubber gasket (make sure it's the correct size for your drain) - Plumber's putty or silicone sealant - Rags or paper towels - Bucket or container to catch water

Step-by-Step Guide:

1. Prepare the Area: - Start by turning off the water supply to the bathtub. - Open the drain to allow any remaining water to drain out. 2. Remove the Drain Stopper: - Use the adjustable wrench to loosen and remove the drain stopper. - Be careful not to drop the stopper into the drain. 3. Remove the Drain Grate: - Use the flathead screwdriver to pry off the drain grate. - Be careful not to damage the grate or the surrounding area. 4. Remove the Old Gasket: - Use the flathead screwdriver to carefully pry off the old gasket from the drain flange. - Be careful not to damage the drain flange. 5. Clean the Drain Flange: - Use a rag or paper towel to clean the drain flange. - Remove any dirt, debris, or old sealant. 6. Apply Plumber's Putty or Silicone Sealant: - Apply a thin layer of plumber's putty or silicone sealant to the drain flange. - Make sure to spread it evenly around the entire surface. 7. Install the New Gasket: - Place the new rubber gasket on the drain flange. - Make sure it's properly seated and flush with the flange. 8. Reinstall the Drain Grate: - Place the drain grate back in its original position. - Press down firmly to secure it. 9. Reinstall the Drain Stopper: - Reinstall the drain stopper by screwing it back into place. - Tighten it securely using the adjustable wrench. 10. Test the Drain: - Turn the water supply back on and allow the bathtub to fill up. - Check for any leaks around the drain. - If there are leaks, tighten the drain stopper or adjust the gasket until the leak stops. 11. Clean Up: - Use a rag or paper towel to wipe up any excess water or debris. - Dispose of the old gasket and any other waste properly. By following these steps, you can easily replace the rubber gasket on your bathtub drain and prevent leaks and water damage. Remember to always turn off the water supply before working on the drain and to use the appropriate tools and materials for the job. If you encounter any issues during the replacement process, it's best to consult a professional plumber for assistance.


How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

Replace Bathtub Drain Shoe Gasket

How To Replace Bathtub Drain Shoe Gasket

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

Replace Bathtub Drain Shoe Gasket

How To Replace Bathtub Drain Shoe Gasket

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

Replacing Tub Drain No Crossbars

Replacing Tub Drain No Crossbars Doityourself Com Community Forums

How To Replace A Bathtub Drain

How To Replace A Bathtub Drain

Bathtub Drain Assembly Stopper Kit

Sento Chrome Lift And Turn Bathtub Drain Assembly Stopper Kit Fit Both 1 2 Inch Or 5 8 Strainer Heavy Duty Metal With Matching S Easy Installation Polished Com


Leave a Reply

Your email address will not be published. Required fields are marked *