Pfister Bathtub Faucet Cartridge Replacement: A Step-by-Step Guide
Pfister is a renowned manufacturer of high-quality bathroom fixtures, including faucets. Their bathtub faucets are known for their durability and style. However, even the best faucets can eventually develop problems, such as a leaky cartridge. If you're experiencing this issue, you can easily replace the cartridge yourself with a few simple tools and our step-by-step guide. ### Step 1: Gather the Necessary Tools and Materials Before you start, make sure you have the following tools and materials on hand: - Adjustable wrench - Phillips head screwdriver - Flat head screwdriver - New Pfister bathtub faucet cartridge - Plumber's putty - Rags - Bucket ### Step 2: Turn Off the Water Supply 1. Locate the water shutoff valves for your bathtub. These valves are usually located underneath the sink or behind the bathtub. 2. Turn the valves clockwise to turn off the water supply. 3. Open the bathtub faucet to release any residual water in the lines. ### Step 3: Remove the Faucet Handle 1. Use the Phillips head screwdriver to remove the screws that hold the faucet handle in place. 2. Once the screws are removed, pull the handle straight off the faucet stem. ### Step 4: Remove the Escutcheon Plate 1. Once the handle is removed, you will see the escutcheon plate. This is the decorative plate that covers the base of the faucet. 2. Use the flat head screwdriver to pry the escutcheon plate off the faucet body. ### Step 5: Remove the Cartridge 1. Once the escutcheon plate is removed, you will see the cartridge. The cartridge is a cylindrical-shaped component that controls the flow of water. 2. Use the adjustable wrench to loosen the cartridge retaining nut. 3. Once the nut is loose, remove the cartridge by pulling it straight out of the faucet body. ### Step 6: Install the New Cartridge 1. Take the new cartridge and insert it into the faucet body. 2. Hand-tighten the cartridge retaining nut until it is snug. 3. Do not overtighten the nut, or you could damage the cartridge. ### Step 7: Reattach the Escutcheon Plate 1. Take the escutcheon plate and align it with the holes on the faucet body. 2. Press the escutcheon plate onto the faucet body until it snaps into place. ### Step 8: Reattach the Faucet Handle 1. Take the faucet handle and align it with the stem. 2. Push the handle onto the stem until it is fully seated. 3. Secure the handle with the screws that you removed in Step 3. ### Step 9: Turn on the Water Supply 1. Go back to the water shutoff valves and turn the valves counterclockwise to turn on the water supply. 2. Turn on the bathtub faucet and check for leaks. If you see any leaks, tighten the cartridge retaining nut or the escutcheon plate until the leak stops. ### Step 10: Test the Faucet 1. Once you're satisfied that there are no leaks, test the faucet by turning it on and off several times. 2. Make sure that the water flows smoothly and at the desired temperature. ### Conclusion Replacing a Pfister bathtub faucet cartridge is a relatively easy task that can be completed in about 30 minutes. By following the steps in this guide, you can save yourself the cost of hiring a plumber.
Genuine Replacement Part 910 3050 Roman Tub Reversible Cartridge For 0x6 040r 140r Pfister Faucets
Genuine Replacement Part 974 2210 Roman Tub Reversible Ceramic Disc Cartridge Pfister Faucets
Factory Direct Plumbing Supply Pfister Replacement Ceramic Tub Cartridge H Or C P099 214h
Genuine Replacement Part 910 3000 Roman Tub Compression Stem Hot Side Pfister Faucets
Genuine Replacement Part 910 8250 Hydroseal Cartridge With Adapter Cold Side Pfister Faucets
Everbilt 4 7 16 In 12 Pt Broach Right Hand Only Cartridge For Pfister Replaces 910 305 39985 The Home Depot
Pfister 974 025
Pfister 974 3210 Pressure Balance Valve Cartridge Sub Assembly
Pfister 2 Handle Brass And Plastic Tub Shower Valve Cartridge In The Faucet Stems Cartridges Department At Com
Genuine Replacement Part 974 2920 Avante Pull And Turn Tub Shower Cartridge Pfister Faucets
